**************************************************************************** ********************** D720200 Design Resources Release ******************** **************************************************************************** Release Note June 15.2012 Renesas Electronics uPD720200 USB3.0 Host Controller Firmware Version : 3.0.3.4 : June 15th, 2012 Copyright (C) 2009-2012 Renesas Electronics Corporation All Rights Reserved **************************************************************************** --------------------------------------------------------------------------- Table of Contents --------------------------------------------------------------------------- 1. Release Files 2. History --------------------------------------------------------------------------- 1. Release Files --------------------------------------------------------------------------- Date Time Size File Name Version 2012/06/14 21:43 32KB F303408.MEM 3.0.3.4 --------------------------------------------------------------------------- 2. History --------------------------------------------------------------------------- --------------------------------------------------------------------------- Version 3.0.3.4 : June 15th, 2012 --------------------------------------------------------------------------- - The following problems are fixed. 1. Fixed the USB3.0 Host Controller in D3hot didn't send the PME Message when it received any wakeup events. 2. The following issue is fixed by ver 2.1.19.0 of RENESAS USB 3.0 Host Controller Driver, but there was a possibility that this could still occur in Windows 8: [RENSAS USB 3.0 Host Controler Driver ver 2.1.19.0's history] 1. USB3.0 devices aren't detected when users perform the below steps. a) Turn on a PC. b) Enter sleep (S3 state) without connecting USB3.0 devices. c) Connect USB3.0 devices to a USB3.0 port during S3 state. d) USB 3.0 HDD isn't detected. The USB3.0 devices aren't detected after the PC resumes from S3 state. With Windows 7 or earlier, this issue only occurs with driver Ver.2.1.16.0. 3. There is a possibility that the USB 3.0 Host controller cannot notify the xHCI Driver when the Host controller receives the following contiguous Device Notification Transaction Packets: Function Wake Notification, Latency Tolerance Message (LTM) Device Notification, Bus Interval Adjustment Message Device Notification. We have never seen this problem on a real system. 4. Improved the interoperability of UAS devices in Windows 8. --------------------------------------------------------------------------- Version 3.0.2.8 : April 22th, 2011 --------------------------------------------------------------------------- -Modified "xHCI Driver yellow bang problem" reported with "Notification and product restriction information Ver1.3 (IBB-NC1-200008)". We found a very rare case that the issue occur even if the Version 3.0.2.7 is applied. --------------------------------------------------------------------------- Version 3.0.2.7 : November 30th, 2010 --------------------------------------------------------------------------- -Modified "xHCI Driver yellow bang problem" reported with "Notification and product restriction information Ver1.3 (IBB-NC1-200008)". --------------------------------------------------------------------------- Version 3.0.2.5 : March 24th, 2010 --------------------------------------------------------------------------- -Modified "xHCI Driver Unload Problem" reported with "Notification and product restriction information Ver1.2 (IBB-ND0-100005)". -Bulk Streaming Protocol is supported. --------------------------------------------------------------------------- Version 3.0.2.1 : November 2, 2009 --------------------------------------------------------------------------- -SuperSpeed Receiver characteristic was changed to improve interoperability of a SuperSpeed Device. To get certain interoperability, please use the devic driver version 1.0.17.0 released at Nov.2nd 2009 or later. -Transfer bandwidth for HighBand Isochronous device was improved. --------------------------------------------------------------------------- Version 3.0.1.6-0.6 : October 6, 2009 --------------------------------------------------------------------------- -uPD720200 with this FW got USB-IF certfication. To get system certification with uPD720200 from USB-IF, this FW or later version of should be used. -Changed timeout value of SuperSpeed transaction. -Modified field check function for the AddressDevice Command. -Modified field check function for the Configure Command. --------------------------------------------------------------------------- Version 3.0.1.3-0.6 : August 24, 2009 --------------------------------------------------------------------------- -Updated major version. This FW is for CS sample whose revision ID of PCI Configuration register is 3h, or is for later revision. -To write this FW, please use D200FW20.EXE(Rom writing tool) released at 09/08/24 or latest version. --------------------------------------------------------------------------- Version 2.0.2.3 : July 17, 2009 --------------------------------------------------------------------------- Note1: This FW is only for the ES sample whose revision ID of PCI Configuration register is 2h. Note2: When writing this FW to the serial ROM connected with uPD720200, please use D200FW11.EXE released at 09/07/17 or latest version. -The following function Added 1. Add a Vender Defined Command. -The following bug fixed 1. Modified Bandwidth calculation algorithm. --------------------------------------------------------------------------- Version 2.0.2.0 : June 15, 2009 --------------------------------------------------------------------------- -The following bug fixed 1. USB Remote wake up function is not worked correctly. --------------------------------------------------------------------------- Version 2.0.1.8 : May 29, 2009 --------------------------------------------------------------------------- -First Release for ES Sample ---------------------------------------------------------------------------